.Direct Vent and B-Vent Gas Fireplace Inserts Model LDV-3, LDV-4, LDV-5, LDV-6 LBV-3, LBV-4, LBV-5, LBV-6 Installation and Owner’s Manual PLEASE NOTE: This product has been manufactured using steel and screws. As a result, there are many sharp edges that can easily cut exposed skin.
It is highly recommended that you wear proper protective gloves while installing the unit, and during routine cleaning or maintenance.Attention Installer The following label has been provided by the manufacturer and MUST be fixed into the installation area. The installer must mechanically attach the marking supplied with the gas fireplace insert to the inside of the firebox of the fireplace into which the gas insert is installed (see label 1.29.7-g).Serial Number: Welcome! Congratulations on the purchase of your new Luxor Gas Fireplace! We hope you’ve had an easy and enjoyable time choosing from our line of products, and we certainly appreciate your business. Please take some time to read through the following information, and make sure to heed all of the warnings.Table of Contents Page 12: Thermostat Installation Page 1: Pre-Start Up Page 2: Table of Contents Page 13: Log Installation Page 3: Specifications Page 14: Log Installation Page 15: Parts List Page 4: Clearances Page 16: Lighting Instructions Page 5: Direct Vent Venting Page 6: B-Venting Page 17: Final Checks Page 18: Trouble Shooting.SPECIFICATIONS Note: Always check appliance label for correct information.
Luxor 3 Activation Code Free
MODEL: Luxor Natural Gas Manifold Pressure 1.6in-3.5in w.c.(0.45-0.87 kPa) Min. Supply pressure for purpose 5.0in - w.c. (1.0 kPa) of input adjustment Max. Supply pressure for purpose 14.0in - w.c. (1.8kPa).WARNING: Cutting any sheet-metal parts off the fireplace in which the gas fireplace insert is to be installed is prohibited. The model Luxor is intended for installation into masonry or listed factory built fireplaces. Masonry fireplaces must be built according to the requirements of the standards for chimneys, fireplaces, vents and solid fuel burning appliances, NFPA 211 (Latest Edition) or the applicable National, Provincial, State or local codes.Note: Only UL Listed 3” Aluminum venting may be used with the model Luxor.
Luxor 4
PLANNING YOUR VENT INSTALLATION This type of direct vent system may only terminate in the following way: Vertical termination using a D uravent 3”.LBV-Venting Exiting fireplace (Masonry or factory built) The model Luxor is intended for installation into masonry or listed factory built fireplaces. Masonry fireplaces must be built according to the requirements of the standards for chimneys, fireplaces, vents, and solid fuel burning appliances, NFPA 211 (latest edition) or the applicable National, Provincial, State, or Local codes.LBV-Venting Vent location The vent terminal must be located through the roof. This ‘b’ vent appliance is designed to operate when an undisturbed airflow hits the outside vent terminal from any direction.
The figure below shows minimum vent cap clearances. Check local codes for allowable vertical vent terminations 2ft Min 2ft Min.Note: Only UL Listed Aluminum (exhaust) 4” flex or listed ‘B’ vent pipe may be used with the model Luxor. The minimum venting required on the gravity vented models for safe operations is 11 feet above the appliance base with one-foot horizontal offset (with 90 degree elbows.).Door Fitting WARNING: Do not abuse the appliance’s glass by striking, slamming or similar trauma. Do not use the appliance with the door removed, glass panel cracked or broken. Only use glass approved for use with this heater. Do not use substitute materials.
Replacement of the panel should only be carried out by a licensed qualified service person.Electrical WARNING Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle. Do not cut or remove the grounding prong from this plug. L1(BK) Fan Motor Variable Speed Control.Planning The recommended order of installation is as follows: 1-Familiarize yourself with this manual. 2-Check the minimum install dimensions and vent installation. 3-Check your local install codes. 4-Check you have the parts and components necessary to complete the installation. 5-Check the gas and electrical supplies are ready.
6-Prepare opening (clean chase, level base etc.) 7-Install Venting.Thermostat Installation Thermostat or wall switch installation The burner control switch is located in the center of the control department opening. For your convenience, the unit can also be operated by a thermostat or a wall switch control. Millivolt thermostats are available from any authorized FDMCo dealer.Log Installation Make certain that none of the fire holes or the pilot are blocked while installing the log set.
Logs are brittle and easily damaged. Handle with care. Distribute vermiculite evenly over the burner. Spread it near and around the flame holes, but do not block any of them.Logs Installation Continued Fiber “ember” material to be placed sparingly across the front of the log set. Careful not to block any of the flame holes. These installation pictures are with the optional Brick Set installed. If you do not have the 3 piece brick set, the background will be black.Parts List Spare Parts Part No.
Description FD-101 #42 Orifice FD-102 #38 Orifice FD-103 SIT Pilot Assembly FD-104 SIT Gas Valve LDBV-DR 3 Door Assembly Log Set LDBV-DR 4 Door Assembly LDBV-DR 5 Door Assembly LDBV-DR 6 Door Assembly Fan Components FF-101Fan kit FF-102 Heat Sensor SIT Pilot Assembly.Lighting Instructions For your safety, read the following before lighting. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage and personal injury or death. This appliance has a pilot which is lit with a push-button piezo lighter. When lighting the pilot, follow these instructions exactly.Final Checks Installer: Before leaving the appliance with the 1. Clean the glass regularly as soon as you notice customer, you must check the operation of the the buildup, (white film). If the film is left for a longer appliance. Period of time, build up will bake on.Trouble Shooting Please check to make sure the instructions are followed exactly before attempting trouble shooting of the appliance.
Warning: Trouble shooting and servicing of gas and electrical devices of the appliance should only be conducted by a qualified service technician. Caution: Label all wires prior to disconnection when servicing controls.Trouble Shooting Continued Corrective Action Possible Cause Problem Adjust pilot and clean if required. Pilot adjusted too low Frequent pilot outage problems Check switch wires. Switch wires may be grounding out Check thermocouple millivolts Thermocouple worn Check termination location and make sure it is not Adverse wind conditions subject to adverse environmental conditions.Maintenance Continued More frequent cleaning may be required due to excessive lint from carpet bedding material etc. It is imperative that control compartments, burners, and circulating passage ways of the appliance to be kept clean. To clean the logs, use a soft paint brush, and to clean the burner compartment, use a vacuum cleaner but take all the logs, vermiculite and embers out.After the first year, with respect to the Luxor Limited Lifetime Warranty, CFH Mfg Inc may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).